Learn how to change your oil

Step-by-step instructions on how to change your oil:

LEARN HOW TO CHANGE YOUR OIL, STEP-BY-STEP INSTRUCTIONS

You are missing some Flash content that should appear here! Perhaps your browser cannot display it, or maybe it did not initialize correctly.

1. Prepare the vehicle before you change your oil. Park it on a level surface, engage parking brake and turn off engine. If necessary, raise the front of the vehicle by driving it onto a ramp or by jacking it up and supporting it with jack stands. CAUTION: WHEN YOU CHANGE YOUR OIL, NEVER GET UNDER A VEHICLE SUPPORTED ONLY BY A JACK! WE ALSO RECOMMEND WHEEL CHOCKS TO HELP PREVENT WHEELS ON THE GROUND FROM ROLLING.

2. Open hood.

3. Locate engine oil dipstick and remove (helps oil flow when draining oil before you change your oil.)

4. Once vehicle is safely and securely supported, put on safety glasses, crawl under vehicle and locate engine's oil pan. (See owner's manual for reference.)

5. Locate oil drain plug, which is a long bolt head at bottom of pan. The drain plug allows the oil to drain out of the pan while you change your oil. (Note: Some vehicles have two drain plugs.)

6. Position a container, such as an approved oil catchpan, under drain plug. Make sure the catchpan is large enough to hold the volume of oil expected to drain out of the engine.

7. Loosen drain plug using box-end wrench or 6-pt. socket. Carefully remove plug by hand, making sure catchpan is underneath plug hole. Oil will flow rapidly from hole, but allow several minutes for all old oil to drain out. (See vehicle owner's manual for additional information.) CAUTION: OIL MAY BE HOT!

8. Wipe the oil pan threads and oil drain plug with a rag and visually inspect the condition of the oil pan and oil drain plug threads and gasket. Buy a replacement drain plug if you have any concerns about the condition of the plug. Replace the drain plug gasket if needed (some OEMs recommend this). Once the oil is finished draining, reinstall the oil drain plug and tighten with the correct box-end wrench or 6-pt. socket to the manufacturer-specified torque. (See owner’s manual.)

9. Locate oil filter. If the old and new oil filters are not the same, double-check the application to be sure you have the correct filter. (See vehicle’s owner’s manual for additional information.)

10. Position oil catchpan under oil filter to catch any residual oil remaining inside filter.

11. Loosen oil filter or oil filter cap with oil filter wrench, and allow oil to drain from oil filter.

12. Remove oil filter. Check to make sure filter gasket has come off with the filter. If it's still clinging to the engine mounting plate, remove it and any remaining residue.

13. Place a light coating of new oil you plan to use when you change your oil on the gasket of the new oil filter so it will install smoothly onto engine. (Note: Do not use grease!) By hand, install new oil filter onto engine by turning in a clockwise direction. Once oil filter gasket first contacts mounting plate gasket surface, tighten filter according to directions for your application (usually found on the new oil filter or oil filter box), preferably by hand. Generally, this is three-quarters to one full turn after the filter gasket contacts the engine. (NOTE: Cartridge oil filter replacement procedures may differ. See owner's or service manual for instructions.)

14. You are now ready to change your oil. Under the hood, remove the oil fill cap and pour in the correct viscosity and amount of Quaker State® motor oil with a funnel. (See vehicle's owner's manual for recommended grade, specification and amount.)

15. Once you change your oil, replace oil fill cap.

16. Start engine and run at idle for minimum of 30 seconds. Carefully inspect under vehicle for oil leaks (especially by oil drain plug and oil filter). If leaks are visible, shut off engine immediately and repair leaks.

17. Shut off engine and allow 30 seconds for oil to settle in the engine. Carefully inspect the area beneath the vehicle for oil leaks.

18. Safely lower vehicle to level ground.

19. Insert and remove oil dipstick to check for proper oil level, adding more oil if necessary. (See vehicle’s owner’s manual for oil capacity and recommended oil level on dipstick.)

20. Change your oil with Quaker State® motor oil as directed by manufacturer’s guidelines.

Note: These instructions are intended as general guidelines. Please consult your owner's or service manual for specific instructions on changing the oil and filter on your vehicle. Use extreme caution when lifting or jacking any vehicle.

Car Care